There are several ways to heat and keep the barrel:
1. Bottom heating method: Put the barrel on a cast aluminum electric heating plate to heat it.
2. Internal heating method: pierce into the barrel with an electric heating rod to heat.
3. External heating method: Use silicon rubber electric heating plate or glass fiber electric heating sheet to surround the barrel to heat. According to different situations, several methods can be used alone or together.
Type: KN-
Power: 500-3000 (W)
Appearance scale: can be determined according to demand.
Main application: heating of barrel
The electric heater of the oil drum is heated to easily take out the liquid and condensate in the drum, such as the adhesive, grease, asphalt, paint, white wax, oil and various resin materials in the drum, and the drum body is heated to make its viscosity Reduce evenly and reduce the power of the pump. Therefore, this equipment is not affected by the season and can be used all year round. The oil barrel heater is equipped with a sensor on the surface, which directly controls the temperature after temperature adjustment.
Figure 1 Bottom electric heater for barrel
Technical Parameters:
Voltage: 220V/380V (single-phase/three-phase) AC 50HZ
Power: 4.5-8Kw
Temperature control scale: 20~300℃
Weight: 35kg
Dielectric strength: 1500V / 1min
Insulation resistance: >1.5mΩ
Figure 2 Silicone rubber electric heating plate for external heating A sensor is installed on the outside of the heater, and the temperature is directly controlled by temperature adjustment.
Standard for silicon rubber electric heating plate:
Cylindrical heater 20 liters Cylindrical heater 20 liters Cylindrical heater 20 liters
Ruler inch 250×1740mm 200×860mm 125×1740mm
Voltage power 220V 2000W 220V 800W 220V 1000W
Temperature adjustment 30～150℃ EGO
The weight is about 0.5kg, about 0.4kg, about 0.3kg. There are several ways to heat the barrel:
1. Bottom heating method: Put the barrel on a cast aluminum electric heating plate to heat it.
2. Internal heating method: pierce into the barrel with an electric heating rod to heat.
3. External heating method: Use silicon rubber electric heating plate or glass fiber electric heating sheet to surround the barrel to heat. According to different situations, several methods can be used alone or together.
Type: KN-
Power: 500-3000 (W)
Appearance scale: can be determined according to demand.
Main application: heating of barrel
The electric heater of the oil drum is heated to easily take out the liquid and condensate in the drum, such as the adhesive, grease, asphalt, paint, white wax, oil and various resin materials in the drum, and the drum body is heated to make its viscosity Reduce evenly and reduce the power of the pump. Therefore, this equipment is not affected by the season and can be used all year round. The oil barrel heater is equipped with a sensor on the surface, which directly controls the temperature after temperature adjustment.
Figure 1 Bottom electric heater for barrel
Technical Parameters:
Voltage: 220V/380V (single-phase/three-phase) AC 50HZ
Power: 4.5-8Kw
Temperature control scale: 20~300℃
Weight: 35kg
Dielectric strength: 1500V / 1min
Insulation resistance: >1.5mΩ
Figure 2 Silicone rubber electric heating plate for external heating A sensor is installed on the outside of the heater, and the temperature is directly controlled by temperature adjustment.
Standard for silicon rubber electric heating plate:
Cylindrical heater 20 liters Cylindrical heater 20 liters Cylindrical heater 20 liters
Ruler inch 250×1740mm 200×860mm 125×1740mm
Voltage power 220V 2000W 220V 800W 220V 1000W
Temperature adjustment 30～150℃ EGO
Weight Approximately 0.5kg Approximately 0.4kg Approximately 0.3kg
